Hakrc F7 MATEK F722 SE Flytower 2-6S 45A 60A 70A X4 ESC speed Flight Controller 30.5mm for Stack Iflight

The Hakrc F7 MATEK F722 SE Flytower is a high-performance flight controller designed for use with quadcopters and other multirotor aircraft. It features a powerful STM32F722RET6 processor with 216MHz clock speed and 512KB flash memory, along with an MPU6000 gyro and accelerometer for accurate and stable flight control. The Flytower also includes a Matek FCHUB-6S PDB, which provides regulated power to the ESCs and other components. The ESCs are Hakrc X4 ESCs, which support up to 6S LiPo batteries and have a continuous current rating of 45A, with burst currents up to 60A or 70A (depending on the model). With its 30.5mm mounting pattern, the Flytower is compatible with a wide range of frames from brands such as iFlight, GEPRC, T-Motor, and EMAX. It also supports a variety of popular flight control software including Betaflight, Cleanflight, and iNav.

Features:

Blheli 32 60A F7 flying tower
Package size Φ 62*33mm
Net weight 40g
Accessories list:
Purple big ball * 8 8p wire * 1 DJI connecting wire * 1 big capacitor (35v470uf) * 1
XT60 power head * 1 red black power cord * 1 small screw * 4 Black nut * 4
There are many integrated functions of the flight control, and the components are very dense. When installing, please do not use tools (such as needle-nosed pliers or sleeves) to screw the nut, which is easy to scratch the tower hardware and cause unnecessary loss.
The correct way is to tighten the nut with your fingers and the screwdriver can quickly tighten the screw from the bottom (Remember not to be too tight, so as not to damage the PCB).
Do not install the propeller when installing and debugging the flight control. Try not to fly indoors to avoid a safety accident.
Before installing the propeller test, check again that the motor is turning and the propeller is in the correct direction.
Safety Tip: Do not fly near the crowd. The company is not responsible for any loss caused by the crash of the aircraft.
Do not use non-original aluminum or nylon columns to avoid damage to the flight control hardware. The official standard is a custom-sized nylon column for the fly tower.
Before the power is turned on, please check whether the installation between the towers is correct (it must be arranged with the pins or cables aligned), check whether the positive and negative poles of the welding are correct, and check whether the motor screws are against the motor stator to avoid short circuit.
Checking the electronic components of the tower for soldering out may result in a short circuit.

Specification:

7230D flight control:
Size: 36x36mm
Packing size: 62*58*17mm
Installation hole distance: 30.5×30.5mm φ4mm
Weight: 6g
Package weight: 20g
Processor: STM32F722RET6
Gyroscope: MPU6000
B E C: 5V/3A; 9V/2.5A
Storage: 16MB
Input voltage: 3-6S
Firmware: betaflight_4.1.0_MATEK722
Uart serial port: 5
Packing list:
HK 7230D flight control motherboard x1,
Damping ring x4,
8p soft silicone wire x1

Technical parameters of 45A electric ESC
Electric adjustment size: 44 * 44 * 6mm
Net weight of electric regulator: 14g
Fixed hole spacing: 30.5 * 30.5mm Φ 4mm
Continuous current: 45A
Maximum current: 50A (lasting for 10s)
Input voltage: 2 — 6S
Parameter adjustment software: blisuite
Drive signal support: dshot150 / 300 / 600, multishot, PWM, oneshot.

Technical parameters of 32-bit 60A electric ESC
Electric adjustment size: 45 * 43 * 6mm
Net weight of electric regulator: 15g
Fixed hole spacing: 30.5 * 30.5mm Φ 4mm
Continuous current: 60A
Maximum current: 65A (lasting 10s)
Input voltage: 2 — 6S
Parameter adjustment software: blheli32
Drive signal support: dshot150 / 300 / 600 / 1200, multishot, PWM, oneshot